Acrylic and PVC sheet can look alike on a quote, but they behave very differently in sunlight, in a fire test, under a laser and in a chemical splash zone. A side-by-side comparison for engineers and buyers choosing between them.
Typical values for general-purpose grades · always check the data sheet of the actual grade
Choose acrylic (PMMA) when the part must be clear, stay clear outdoors, polish to a glass-like edge or be laser-cut cleanly. Choose rigid PVC when the part must resist acids and alkalis, carry a better fire classification, or take knocks at the lowest material cost, and when optical clarity does not matter. Acrylic transmits about 92% of visible light and weathers for years without yellowing; clear PVC transmits less and tends to yellow in sunlight. PVC is tougher and self-extinguishing; acrylic is harder on the surface but more brittle and combustible. One practical rule matters on the shop floor: acrylic is laser-cut every day, while PVC must never be laser-cut, because it releases chlorine compounds that harm people and machines.
Acrylic vs PVC, property by property
| Property | Acrylic (PMMA) | Rigid PVC |
| Light transmission (clear, 3 mm) | About 92% | Lower; clear grades are often slightly blue or grey |
| Outdoor UV stability | Very good; stays clear for years | Yellows and loses clarity without UV-stabilised grades |
| Density | About 1.19 g/cm³ | About 1.4 g/cm³, so heavier per panel |
| Impact strength | Higher than glass, but brittle compared with PVC | Tougher; dents or cracks less readily |
| Surface hardness | Harder; resists light scratching better | Softer; marks more easily |
| Service temperature | Softens around 95–105 °C for cast sheet | Softens at a lower temperature, roughly 65–80 °C |
| Fire behaviour | Combustible; burns with little smoke | Self-extinguishing; produces dense, corrosive smoke |
| Chemical resistance | Poor with solvents, alcohols and many cleaners | Good with acids, alkalis and salts; used for tanks and ducting |
| Laser cutting | Clean, flame-polished edge | Do not laser-cut: releases chlorine compounds |
| Edge polishing | Polishes to an optical, glass-like edge | Polishes poorly; edges stay matt |
| Bonding | Solvent bonding gives a clear, near-invisible joint | PVC solvent cement or welding; joints are visible |
Values are typical ranges for general-purpose grades reported in material data sheets. Impact-modified, UV-stabilised and fire-retardant grades of both materials shift these numbers, so the data sheet for the exact grade decides.
Which one to choose, by application
| Application | Usually | Why |
| Machine guards and viewing windows | Acrylic, or polycarbonate where impact is high | Clarity for the operator; see acrylic vs polycarbonate for guards |
| Display cases, POP and signage faces | Acrylic | Optical edges, clear solvent-bonded joints, laser-cut detail |
| Backlit and translucent wall panels | Acrylic | Even light transmission and long-term colour stability |
| Chemical tanks, fume ducting, plating lines | PVC | Resistance to acids and alkalis; weldable |
| Wet-area wall linings with no clarity need | PVC | Lower cost, tough, easy to install |
| Outdoor clear glazing | Acrylic | Does not yellow; see acrylic UV resistance |
| Parts that must meet a strict fire class | Check the code first | PVC classifies better, but smoke and toxicity limits may rule it out; see acrylic fire ratings |
Mistakes we see on drawings
| Mistake | What happens | Fix |
| “Clear plastic” with no material named | Quotes come back in different materials and are not comparable | Write PMMA (cast or extruded) or PVC, plus grade and thickness |
| Acrylic specified near solvents or alcohol cleaners | Crazing and cracks at holes and bends | Change the cleaner or the material |
| Laser cutting called up on a PVC part | Toxic fumes and damaged laser optics | Route or saw PVC; laser-cut only acrylic |
| PVC chosen for a sun-facing clear panel | Visible yellowing within a few seasons | Use UV-stable acrylic |
What we work
AcrylicFabWorks, the acrylic division of SinoPlastix, works acrylic only. We do not cut or supply PVC, PETG or HDPE, so if your part is better in PVC we will say so rather than quote acrylic for it. For acrylic parts we use Calypto cast acrylic sheet, cast on our own line in Suzhou, China, or branded PMMA when your specification names one, and cut, machine, bend, bond and polish it in one ISO 9001 plant. For the other plastics buyers compare acrylic with, see acrylic vs PETG and acrylic vs polycarbonate.
FAQ
Is acrylic or PVC clearer?
Acrylic. Clear acrylic transmits about 92% of visible light and stays clear outdoors, while clear PVC transmits less and tends to yellow in sunlight.
Is PVC stronger than acrylic?
PVC is tougher and less likely to crack on impact. Acrylic is harder on the surface and stiffer, but more brittle.
Can you laser-cut PVC like acrylic?
No. Laser-cutting PVC releases chlorine compounds that are harmful to people and corrode the machine. Acrylic laser-cuts cleanly with a flame-polished edge.
Which is better for chemical resistance?
PVC, for acids, alkalis and salts. Acrylic is attacked by many solvents, alcohols and aggressive cleaners.
Specifying a clear part?
Send the drawing and the environment it works in. We reply within 12 hours.
Or email [email protected]