Acrylic vs PETG Sheet: Clarity, Toughness, Forming and Cost

Heat-formed clear acrylic display stand

PETG is the plastic most often quoted against acrylic for displays, guards and covers. It is tougher and easier to form; acrylic is clearer, harder, better outdoors and far better at polished edges and laser cutting. How to decide for your part.

Typical values for general-purpose grades · always check the data sheet of the actual grade

Choose acrylic (PMMA) when appearance decides: higher clarity, a harder surface, a polished or laser-cut edge, invisible solvent-bonded joints and long outdoor life. Choose PETG when the part will be dropped, flexed or knocked, or must be thermoformed into deep shapes at low cost, and a slightly softer, less brilliant surface is acceptable. PETG is many times tougher than acrylic and forms at lower temperatures without pre-drying, but it scratches more easily, softens at a lower temperature, does not take a polished edge and does not laser-cut cleanly. For displays that must look new across a long retail rollout, acrylic usually wins; for low-cost formed covers and protective shields, PETG often does.

Acrylic vs PETG, property by property

Property Acrylic (PMMA) PETG
Light transmission (clear, 3 mm) About 92% About 88–90%
Impact resistance Higher than glass, but brittle Much tougher; resists cracking when dropped or drilled
Surface hardness Harder; better scratch resistance Softer; scuffs and scratches more easily
Service temperature Softens around 95–105 °C for cast sheet Softens around 70–80 °C
Outdoor UV stability Very good without additives Can yellow outdoors unless a UV grade is used
Thermoforming Needs higher heat; good for domes and covers Forms easily at lower temperature, deep draws, no pre-drying
Cold bending and drilling Cracks if bent tight or drilled carelessly Tolerates cold bending and drilling well
Laser cutting Clean, flame-polished edge Melts and discolours; usually routed or sawn
Edge polishing Diamond or flame polish to a glass-like edge Does not polish well
Bonding Solvent bonding gives near-invisible joints Harder to bond invisibly; adhesives or mechanical fixing
Chemical resistance Poor with solvents and alcohols Better with many cleaners and dilute chemicals

Values are typical ranges from material data sheets for general-purpose grades. Impact-modified and UV-stabilised acrylic grades close part of the gap on toughness; the data sheet for the exact grade decides.

Which one to choose, by application

Application Usually Why
Premium retail displays and cases Acrylic Polished edges, invisible joints, stays clear through a rollout; see acrylic POP displays
Short-life promotional displays PETG Lower cost, survives shipping knocks
Deep-formed covers and trays PETG Forms easily at low temperature
Equipment windows and enclosures Acrylic Clarity, scratch resistance, machined features; see equipment enclosures
Guards that may be struck Check impact risk first PETG or polycarbonate where impact is high; acrylic where visibility and scratch resistance matter more; see specifying impact resistance
Outdoor clear panels Acrylic No yellowing without additives
Medical and food-contact parts Check the grade Both have compliant grades; certification belongs to the specific grade, not the polymer

Cost: compare the finished part, not the sheet

PETG and acrylic sheet prices move with resin markets, so a per-kilogram comparison only holds for the week it is made. What changes the finished-part cost more is the process each material allows. Acrylic laser-cuts with a finished edge, so a part can go from sheet to packing without an edge-finishing step. PETG usually has to be routed and its edges cleaned. On the other hand, PETG forms without pre-drying and at lower temperature, which saves time on deep-formed parts. Quote the same drawing in both materials, with the edge finish and forming steps written out, and compare those numbers. Our guide to how acrylic sheet is priced explains the sheet side.

What we work

AcrylicFabWorks, the acrylic division of SinoPlastix, works acrylic only. We do not supply or fabricate PETG, so if PETG is the better material for your part we will tell you. Acrylic parts are made from Calypto cast acrylic sheet, cast on our own line in Suzhou, China, or from branded PMMA when your specification names one, and are cut, machined, bent, bonded and polished in one ISO 9001 plant. Samples take 48 hours and production 7 days from drawing approval.

FAQ

Is PETG stronger than acrylic?

PETG is much tougher and less likely to crack when dropped, drilled or bent. Acrylic is stiffer and harder on the surface, but more brittle.

Is acrylic or PETG clearer?

Acrylic, at about 92% light transmission for clear sheet against about 88–90% for PETG, and acrylic edges can be polished to a glass-like finish.

Can PETG be laser-cut like acrylic?

Not cleanly. PETG tends to melt and discolour under a laser, so it is usually routed or sawn. Acrylic laser-cuts with a flame-polished edge.

Which is better outdoors?

Acrylic. It resists UV without additives and stays clear for years, while standard PETG can yellow outdoors unless a UV-stabilised grade is used.

Choosing a material for a clear part?

Send the drawing and how the part is used. We reply within 12 hours.

Or email [email protected]

← All articles Request a Quote